manufacturing menagement
Casse 2.1 fostex pm1 sub fostex pm5
VENDO COPPIA CASSE FOSTEX PM1 E SUB FOSTEX PM5 CARATTERISTICHE CASSE: It's a little-known fact that Fostex are one of the world's largest manufacturers of loudspeaker drive units, most destined for consumer products such as in-car systems. This manufacturing expertise has been applied to their new PM1 active studio monitor, a two-way system featuring a one-inch soft-dome tweeter and a 6.5-inch bass/mid-range driver, powered respectively by 45W and 75W discrete bipolar transistor amplifiers. The cabinets measure a compact 215 x 380 x 283mm, including the rear-panel heat sink, and two bass reflex ports are fitted through the front baffle. A discrete green LED set into the Fostex badge shows when the power is on. At 11kg each, these are not excessively heavy for active monitors, but they feel substantial and well built. Unusually, there's very little technical information available on the finer points of the driver design, though outwardly they appear to be fairly conventional and, despite their rather compact size, they have a frequency response stated as 50Hz-20kHz 2dB, with the LF and HF -10dB points at 38Hz and 23.5kHz respectively. The crossover type and frequency is not disclosed in the documentation, and there's no frequency-response graph, though we are told that the maximum short-term SPL is 105dB. This is a peak-handling figure, however, and is applicable only to the 80Hz-3kHz range, so I'd imagine a comfortable nominal maximum SPL would be between 85dB and 90dB in practice. While not making these speakers excessively loud, this figure should be more than adequate for sensible nearfield monitoring situations. Physically, the cosmetics of the cabinet design are very plain, with a slight radius to the baffle sides and no grilles. The drivers are mounted centrally and are recessed flush into the baffle, with a rubber-like trim ring around the bass/mid-range unit. The rear panel houses the IEC mains inlet and power switch, as well as a combi jack/XLR
Metabones adattatore da Nikon G a Sony E-mount
Ips: Before mounting your lens to the adaptor, please make sure that the f-stop of aperture ring on the adaptor is turned to "7" (i.e. mounting your lens to the adaptor while only the aperture ring in the adaptor is full closed.). The tripod foot is Detachable and compatible with Arca Swiss, Markins, Photo cam ball head Why Metabones? Since its inception, Metabones has been designing and manufacturing lens adapters recognized among professionals and enthusiasts as leaders in design and workmanship. Contrary to the popular trend of other factories using an aluminum ring painted black on the camera-body-side, we instead take no short-cut but use precision-machined brass with chromium plating on both the camera-body and the lens sides of our adapters, in order to ensure smooth mounting, great appearance, and durability. The lens side of the adapter features a strong leaf-spring structure, strengthening the adapter-lens connection and ensuring tightness of the lens in order to reduce wear and prevent focus errors and optical alignment issues from appearing. Metabones uses matte-black treatment to keep internal reflection to a minimum in order to maintain the maximum optical quality possible with the lens. All Metabones Adapters follow this tradition of uncompromising precision, robust build quality and outstanding finish. Our new Smart AdapterTM series of products add industry-leading electronic interfacing technology from Canada, with true electronic control of the lens', aperture directly from the camera body. Features Both camera-side and lens-side of the adapter are made of brass, precision-machined and plated with chromium. Satin surface finish - just like your OEM lens and camera mounts. Precise fit and solid connection - lens has no play, gap or wiggling when mounted on adapter and no adjustments are required to fit your lens. Designed to reach infinity focus while maintaining the correct registration distance required to maintain optical quality of CRC lenses or lenses with floating elements. Our Smart AdapterTM series adapters have the following additional features True electronic integration of aperture diaphragm - let camera automatically choose aperture in P or S exposure modes, or dial in yourself on the camera body in A or M modes. EXIF data such as lens identification, focal length and aperture.
Metabones adattatore da Nikon G a micro Quattro terzi 4/3
Tips: Before mounting your lens to the adaptor, please make sure that the f-stop of aperture ring on the adaptor is turned to "7" (i.e. mounting your lens to the adaptor while only the aperture ring in the adaptor is full closed.). The tripod foot is Detachable and compatible with Arca Swiss, Markins, Photo cam ball head Why Metabones? Since its inception, Metabones has been designing and manufacturing lens adapters recognized among professionals and enthusiasts as leaders in design and workmanship. Contrary to the popular trend of other factories using an aluminum ring painted black on the camera-body-side, we instead take no short-cut but use precision-machined brass with chromium plating on both the camera-body and the lens sides of our adapters, in order to ensure smooth mounting, great appearance, and durability. The lens side of the adapter features a strong leaf-spring structure, strengthening the adapter-lens connection and ensuring tightness of the lens in order to reduce wear and prevent focus errors and optical alignment issues from appearing. Metabones uses matte-black treatment to keep internal reflection to a minimum in order to maintain the maximum optical quality possible with the lens. All Metabones Adapters follow this tradition of uncompromising precision, robust build quality and outstanding finish. Our new Smart AdapterTM series of products add industry-leading electronic interfacing technology from Canada, with true electronic control of the lens', aperture directly from the camera body. Features Both camera-side and lens-side of the adapter are made of brass, precision-machined and plated with chromium. Satin surface finish - just like your OEM lens and camera mounts. Precise fit and solid connection - lens has no play, gap or wiggling when mounted on adapter and no adjustments are required to fit your lens. Designed to reach infinity focus while maintaining the correct registration distance required to maintain optical quality of CRC lenses or lenses with floating elements. Our Smart AdapterTM series adapters have the following additional features True electronic integration of aperture diaphragm - let camera automatically choose aperture in P or S exposure modes, or dial in yourself on the camera body in A or M modes. EXIF data such as lens identification, focal length and aperture.
Office Manager
Outpost24 is a leading cyber assessment company focused on enabling its customers to achieve maximum value from their evolving technology investments. By leveraging our full stack security insights to reduce attack surface for any architecture, Outpost24 customers continuously improve their security posture with the least effort. Over customers in more than 40 countries around the world trust Outpost24 to assess their devices, networks, applications, cloud and container environments and report compliance status for government, industry sector, or internal regulations. Founded in , Outpost24 serves leading organizations across a wide range of segments including financial and insurance, government, healthcare, retail, telecommunications, technology, and manufacturing. Are you an outgoing, friendly and service minded person who loves helping people and enjoys working in a high-paced environment? Then this might be the role for you. Outpost24 is now looking for our next Office Manager in Copenhagen. The Office Managerâs tasks are mainly to support the office so that it runs smoothly. The Office Manager will organize and coordinate administration duties and office procedures and create and maintain a pleasant work environment to sure high level of organizational effectiveness, communication and safety. As an Office Manager you will be responsible for: Supporting the Employeeâs in the office with ad hoc tasks, e.g. preparing for meetings. Ensure all needed necessities are available (drinks, fruit, furniture, coffee, toilet articles etc.). Host visitors and answering the office phone Support the Finance department with some financial activities such as but not limited to: payroll administration, office budget Support the HR department with on- and off boarding of employeeâs, organize local Christmas party, keep an overview of birthdays and holidays. Order flight and hotel tickets for Employees Support the Marketing department in local events if required. We see that you have great time management skills, have an ability to multi-task and prioritize work. You have a great attention to details and loves working pro-actively and is motivated by going the extra mile for your colleagues. You have excellent communication skills, both verbal and written and you are fluent in English. This role is ideal for a student, as this is a part-time role with approx. 8 â 10 hours per week. Do you feel this role is for you? Please donât hesitate to send in your application as soon as possible. This position will remain open for application until the role is filled.  As part of the recruitment process you must be able to pass a background check in order to qualify for this position.
Philips 193V5LSB" LED VGA Monitor nuovo
Vendo questo monitor Philips 193V5LSB" LED VGA a causa di un doppio regalo. Nuovissimo, ancora nello scatolo, mai acceso. Aspect ratio 16:9 Contrast ratio (typical) Display brightness 200 cd/m2 Display resolution x 768 pixels Philips 193V5LSB" LED VGA Monitor Product Description Great LED images in vivid colours Enjoy vivid LED pictures on this Philips display. Equipped with SmartControl lite, it's a great choice! Highlights Vivid pictures every time LED technology for vivid colours Easy display performance tuning with SmartControl Lite SmartContrast for rich black details Great choice Mercury Free eco-friendly display Compact design saves space VESA mount allows for flexibility Features Easy display performance tuning with SmartControl Lite SmartControl Lite is the next generation 3D icon-based GUI monitor control software. This allows the user to fine-tune most parameters of the monitor like Colour, Brightness, screen calibration, Multimedia, ID management etc with the mouse. SmartContrast for rich black details SmartContrast is a Philips technology that analyses the contents you are displaying, automatically adjusting colours and controlling backlight intensity to dynamically enhance contrast for the best digital images and videos or when playing games where dark hues are displayed. When Economy mode is selected, contrast is adjusted and backlighting fine-tuned for just-right display of everyday office applications and lower power consumption. Mercury Free eco-friendly display Philips monitors with LED backlighting are free of Mercury content, one of the most toxic natural substances, which affects humans and animals. This allows for an eco-friendly display throughout its life-cycle, from manufacturing to disposal. LED technology for vivid colours White LED's are solid state devices which light up to full, consistent brightness faster saving startup time. LED's are free from mercury content, which allows for eco-friendly recycling and disposal process. LED's allow for better dimming control of the LCD backlight, resulting in a super high contrast ratio. It also gives superior colour reproduction thanks to consistent brightness across the screen. Technical Specification Display 18.5" Screen TFT-LCD panel W-LED backlight Resolution x Hz Contrast ratio (typical) Aspect ratio 16:9 Brightness 200 cd/m² Response time 5ms Pixel pitch 0.3 x 0.3mm Viewing angle: horizontal/vertical: ° Colour depth 16.7M Power Power supply: V AC (built-in) Power consumption: 8.76W Power consumption in Standby mode: 0.5W Connectivity VGA Features VESA 100 x 100 Tilt -3/10 Kensington Security lock Plug and Play Compatibility: DDC/CI, Mac OS X, sRGB, Windows 7, Windows 8 Dimensions With stand: 437 x 338 x 170mm (WxHxD) Without stand: 437 x 273 x 48mm
Senior Project Managers and/or Partner - Munich
SYSTEMIQ is an organisation driving system change in clean energy, circular material solutions and sustainable land use. By addressing failures in these areas, SYSTEMIQ aims to unlock economic opportunities that benefit business, society and the environment. We connect the right people, ideas, technologies, and capital to transform economic systems. We do this through five activities: Convene and support coalitions of leaders to shape policies and business strategies that will rapidly transform economic activity Work with companies that want to be pioneers in and drivers of change towards more sustainable systems Co-create and incubate the market solutions most likely to build regenerative economic systems Invest our own venture capital and expertise in opportunities with the biggest potential to drive rapid system change Direct larger pools of capital into regenerative economic systems, so that these scale and multiply. In order to deliver in these areas, we recruit and develop distinctive and varied individuals who strive to achieve our mission, challenge the status quo and act as change leaders.  We are looking for experienced project managers to lead teams on exciting opportunities. This highly strategic work involves some of the most prominent institutions in the field, has a very international character and aims at significant impact over the next 3-5 years. It requires very advanced problem solving, analytical and relationship skills and the experience of leading project teams to deliver breakthrough insights, action and results. Our teams are typically small (2-5 people) and you might be involved in more than one project/venture at a time. Occasionally, you may be working with one of our partners in a standalone capacity. We offer the opportunity to benefit from the world-leading networks of our partners and be part of a high-calibre, driven, and fun/friendly team. There is also the possibility to gain experience in project development and venture capital. SYSTEMIQ is looking for individuals with a strong record of excellence and achievement. You have proven that in different contexts and are keen to work in a young, entrepreneurial company where you can get involved in a variety of work, shape the business and make maximum impact. You are passionate about SYSTEMIQ's mission and approach to system change. Your background includes leading teams at a top management consultancy, ideally coupled with solid leadership experience in industry, the public sector or civil society. Specifically, you have: Many years of top management consulting experience in a high calibre and international environment, ideally working with industry, energy, manufacturing and/or agricultural clients Experience as project/engagement manager, leading teams on both content and process Highly advanced problem-solving and analytical skills, both quantitative and qualitative, with a focus on strategic challenges Relationship management skills, also on a very senior level and in various cultural contexts A strong commitment to coaching and developing people, with an empowering leadership style Strong entrepreneurial spirit with the ability to identify growth opportunities and take a lead in exploring new ideas and concepts Masters or equivalent degree - chemistry/engineering & other Sciences especially welcome Willingness to travel (Desirable) Experience in the sustainability/environment/social enterprise space  Experience in the EV/Mobility/Automotive sector would also be advantageous We are keen to receive applications from all parts of the global community Please send your application to Michael Round at h. You must have Right to Work in Germany Â
Sirui Treppiedi S--N carbonio 5 sezioni SN
Sirui',s S--N Carbon Fiber Tripod weighs 2.6 lb and yet can support up to 26.4 lb. The S--N has individual leg spreading capability for low angles or uneven terrain. Besides the standard center column a short center column is included which allows the tripod to get down to 7". One of the legs is removable to convert to a monopod. When folded, the tripod is 17.7" long, and only 1.6" thick. 8 Layers of Carbon Fiber for Superior Load CapacityThe use of 100% carbon fiber and 8 cross pattern layers makes Sirui tripods and monopods capable of supporting impressive load capacities, while providing a lightweight product. In addition to providing high strength and low weight, carbon fiber is also highly resistant to temperature changes, friction (no need for lubrication) and corrosion.Custom Anodized Surface TreatmentAll Sirui products undergo a special anodized surface treatment that makes any metal surfaces highly resistant to wear and increases durability and weather resistance. Anodizing is an environmentally safe electrochemical process. This also prepares the surface to provide better adhesion of colored finishes.Temperature Tolerance TestPhotographers often work in extreme environments, like blazing deserts or sub-zero mountaintops. It is vital that your equipment works under these conditions. That is why all of these products are "torture-tested" under conditions that far exceed what most people will ever experience: -F (-C).Certified Longevity Tests for Quality and ReliabilityTo confirm the quality and reliability of Sirui tripods (and dedication to details), an independent testing lab (SGS) subjected the leg angle lock spring mechanisms to exhaustive longevity tests. The test reports show that even after actuations, the springs continued to perform perfectly.Short Center ColumnAllows low angle shooting for unique perspectives and macro photography.Precision Leg TubesThe difference in diameter of leg tubes is only 3.0mm from tube to retracted tube. Thanks to precision manufacturing, the legs open and close easily, while the small diameter difference provides added leg stability.Half-turn Leg LocksTo lock the legs of Sirui tripods/monopods, twisting locks are utilized for maximum reliability and stability. Simply twist the rubber leg locks 1/2 turn and the legs will extend by themselves.Unique Locking SystemThe Sirui S-N series tripods have a unique leg position locking system that clicks in place when the tripod is opened. This guarantees that the tripod legs will be properly positioned -providing a rugged, stable support for your equipment. Simply open the tripod in the direction of the arrows until it clicks into place. When you',re done shooting, press the red unlock button and close the tripod flat.Non-Twist Center Column/LegsAll Sirui center columns and legs have keyed, grooved channels that prevent twisting, providing additional stability and safety for your photographic equipment.Converts to MonopodThe detachable leg lets you transform your tripod into a monopod, this reduces the amount of equipment you need to carry and makes your camera bag or backpack lighter. Maximum Height Tripod: cm) Monopod: cm) Maximum Height w/o Column Extended Tripod: cm) Minimum Height mm) Folded Length Length: cm) Depth: 1.6" (4 cm) Leg Tube Diameters Maximum: mm) Minimum: mm) Load Capacity 26.4 lb (12 kg) Leg Sections 5 Leg Lock Type 1/2 Turn Leg Locks Independent Leg Spread Yes Center Column Sections Standard: 2, short column: 1 Center Column Type Manual Center Brace No Feet Retractable spiked feet Head Type None Head Mount Thread Size Reversible and Weight 2.6 lb (1.2 kg)
Classè SIGMA SSP
Preamplificatori Multicanale Serie Sigma Preamplificatore/processore multicanale a 7.1 canali. 3D e HDMI 1.4. 3D. Streaming da rete, da MAC/PC, dispositivi iOS e da HD/Nas esterno. Airplay e DLNA. Decoder Dolby TrueHD e DTS HD Master Audio, Dolby Digital, Dolby Pro Logic IIx, DTS, DTS-ES, DTS Neo:6. DSP applicabile a tutti gli ingressi con equalizzatore parametrico a nove bande. By-pass per stereo. DAC 24bit/192KHz. Display TFT centrale. 2 ingressi USB asincroni (1 frontale e 1 posteriore), 1 presa Ethernet, 2 ingressi ottici e 3 coassiali, 1 uscita coassiale. 3 ingressi audio analogici di cui uno XLR. Pre out 7.1 con i frontali anche in XLR. 8 ingressi (di cui 1 sul frontale) e 1 uscite HDMI 1.4a. RS-232. Trigger IN/OUT. Controllo IR IN/OUT. RJ45 per bus dati. Uscita cuffia. Telecomando. Elegante finitura in alluminio spazzolato nero. A variety of connection options supports virtually any source optimally: Stream audio asynchronously from a computer, storage device or the Internet via the Sigma SSPâs Ethernet connection. The Sigma SSP supports both AirPlay and DLNA streaming. Front and rear panel USB connections support asynchronous streaming from computers and iOS devices. Eight HDMI inputs (including one on the front panel) provide the optimum path for Blu- ray players, games and set-top boxes while simplifying system connections. The Audio Return Channel lets YouTube, Netflix and other online sources decoded at your display play through the Sigma SSP by using the HDMI connection between them. Coax and optical are provided for those sources lacking the HDMI option. DSP options for improving performance are available to all sources. Bass management, a nine-band Parametric EQ and digital domain Tone Control with our Tilt feature ensure that the system can be optimized for your speak - ers and room, and every source sounds its best. An optional phono stage with custom loading may be fitted to accommodate MM and MC cartridges. The Sigma SSP owes its outstanding performance and value to the unique engineering and manufacturing capa - bilities of ClassĂŠ in MontrĂŠal and the B&W Group globally. No other high-end audio designers have access to the resources necessary to deliver such a product at such a competitive price. The Sigma SSP has been conceived and built as an example of quality and value without peer. It will stand as the seminal reference in the preamp/pro - cessor category for many years to come. Modern high-end audio systems tend to fall into one of two broad categories: stereo and theater. But rarely are they used exclusively in those roles. Most have a television display of some kind between stereo speakers or use the surround sound system for playing music. Inevitably, each makes compromises as it tries to accommodate the requirements of the other. The Sigma SSP is designed to build a bridge between these two categories, optimized as a stereo preamp/processor but with HDMI switching and 7.1 channels of high-performance multichannel processing included. The stereo preamp/processor circuitry is derived from the latest generation Delta series CP-800, making the Sigma SSP a stunning performer as a stereo preamp. Test bench measurements are exceptional and suggest comparison with cost-no-object designs. Sonically the Sigma SSP out-performs stereo preamps with stand-alone DACs, while offering superb decoding of high-resolution formats including Dolby TrueHD and DTS-HD Master Audio. Sigma SSP
Sirui Treppiedi S--N carbonio 4 sezioni SN
Sirui',s S--N Carbon Fiber Tripod is a complete departure from the old days of "lugging around" a heavy metal tripod. To begin with, it only weighs 2.2 lb and yet can support up to 26.4 lb. The S--N is so versatile in its adjustments that it does about anything you can think of short of bending. It has individual leg spreading capability for low angles or uneven terrain. Besides the standard center column a short center column is included which allows the tripod to squat way down. And it reverses for even lower perspectives. The icing on the cake is a removable leg that converts to a monopod. And when the shoot is over the S--N won',t take up much space either. It folds flat to a mere 1.6" thick. 8 Layers of Carbon Fiber for Superior Load CapacitySirui is one of the few manufacturers who make their own carbon fiber leg tubes. The use of 100% carbon fiber and 8 cross pattern layers makes Sirui tripods and monopods capable of supporting impressive load capacities, while providing a lightweight product. In addition to providing high strength and low weight, carbon fiber is also highly resistant to temperature changes, friction (no need for lubrication) and corrosion.Custom Anodized Surface TreatmentAll Sirui products undergo a special anodized surface treatment that makes any metal surfaces highly resistant to wear and increases durability and weather resistance. Anodizing is an environmentally safe electrochemical process. This also prepares the surface to provide better adhesion of colored finishes.Temperature Tolerance TestPhotographers often work in extreme environments, like blazing deserts or sub-zero mountaintops. It is vital that your equipment works under these conditions. That is why all of these products are "torture-tested" under conditions that far exceed what most people will ever experience: -F (-C).Certified Longevity Tests for Quality and ReliabilityTo confirm the quality and reliability of Sirui tripods (and dedication to details), an independent testing lab (SGS) subjected the leg angle lock spring mechanisms to exhaustive longevity tests. The test reports show that even after actuations, the springs continued to perform perfectly.Short Center ColumnAllows low angle shooting for unique perspectives and macro photography.Precision Leg TubesThe difference in diameter of leg tubes is only 3.0mm from tube to retracted tube. Thanks to precision manufacturing, the legs open and close easily, while the small diameter difference provides added leg stability.Half-turn Leg LocksTo lock the legs of Sirui tripods/monopods, twisting locks are utilized for maximum reliability and stability. Simply twist the rubber leg locks 1/2 turn and the legs will extend by themselves.Unique Locking SystemThe Sirui S-N series tripods have a unique leg position locking system that clicks in place when the tripod is opened. This guarantees that the tripod legs will be properly positioned -providing a rugged, stable support for your equipment. Simply open the tripod in the direction of the arrows until it clicks into place. When you',re done shooting, press the red unlock button and close the tripod flat.Non-Twist Center Column/LegsAll Sirui center columns and legs have keyed, grooved channels that prevent twisting, providing additional stability and safety for your photographic equipment.Converts to MonopodThe detachable leg lets you transform your tripod into a monopod! This reduces the amount of equipment you need to carry and makes your camera bag or backpack lighter. Maximum Height Tripod: cm) Monopod: cm) Maximum Height w/o Column Extended Tripod: cm) Minimum Height mm) Folded Length Length: mm) Depth: cm) Leg Tube Diameters Maximum: mm) Minimum: mm) Load Capacity 26.4 lb (12 kg) Leg Sections 4 Leg Lock Type Twist locks Independent Leg Spread Yes Center Column Sections Standard: 2, short column: 1 Center Column Type Rapid Center Brace No Spiked Feet Rubber Head Type None Head Mount Thread Size Reversible and Weight 2.2 lb (1.0 kg)
Metabones adattatore da Canon EF a Sony E-mount Mark IV
Electronic aperture, EXIF, image stabilization, autofocus Your PayPal receipt is your order confirmation. There is no separate email confirmation until shipment takes place. This Smart AdapterTM has the following features: True electronic integration of aperture diaphragm - let camera automatically choose aperture in P or S exposure modes, or dial in yourself on the camera body in A or M modes. Powered by camera body. No external power source required. Wide open button (opposite of depth-of-field preview function) makes manual focusing easy. The tripod foot is detachable and compatible with Arca Swiss, Markins, Photo cam ball heads. High performance 32-bit processor and efficient switched-mode power supply. Flocking material coating inside the inner hole to reduce the internal reflection. Enhancement on new MARK IV (MB_EF-E-BT4) vs. old MARK IV (MB_EF-E-BM4): The inner hole is painted with flocking material coating. This can further reduce the internal reflection. Disclaimer: we are NOT licensed, approved or endorsed by Sony or Canon. Description Compatibility Supported Not supported EF lenses (see below for list of tested lenses) EF-S lenses (see note 1) Image stabilization (IS) lens Electronic manual focusing (e.g. EF L II and discontinued EF L) EXIF (focal length, aperture, zoom range) P, A, S, M exposure modes Autofocus (see autofocus support section below) Distance and zoom display on VG and FS series camcorders (see note 3) Auto magnify (see note 2) Contax N mount lenses modified to Canon EF by Conurus Contax 645 NAM-1 adapter modified to Canon EF by Conurus Sigma, Tamron and Tokina lenses in Canon EF mount (see note 3) Lens correction such as peripheral shading, CA and distortion Focus confirmation "chip" (e.g. Dandelion) Stacking another lens mount adapter on top (see note 4) Lens: Tamron SP mm F/2.8 XR Di II VC Note: 1. Vignetting at corners may occur for certain EF-S lenses because they are designed to cover a 1.6x crop image circle but Sony NEX has a 1.5x crop sensor. 2. Requires lenses supporting distance information. 3. A third party zoom lens may need to be registered with the Smart Adapter first in order to detect its maximum aperture. Autofocus is disabled for most third-party lenses. 4. For example, some improperly-made M42 screw mount adapters may cause a short-circuit with the electronic contacts of the Smart Adapter and cause damage to the Smart Adapter and/or camera body. Tested Camera Bodies A7S (Mark IV supports auto "APS-C Size Capture" with EF-S lens) - Smart Adapter with firmware V0.32 or later A7R (Mark IV supports auto "APS-C Size Capture" with EF-S lens) A7 (Mark IV supports auto "APS-C Size Capture" with EF-S lens) PXW-FS7(autofocus works only in photo mode, but is disabled in movie capture mode) - Smart Adapter with firmware V0.40 or later NEX-FS700 (autofocus works only in photo mode, but is disabled in movie capture mode) NEX-FS100 (autofocus works only in photo mode, but is disabled in movie capture mode) NEX-EA50 NEX-VG900 (Mark IV supports auto "APS-C Size Capture" with EF-S lens) NEX-VG30 NEX-VG20 NEX-VG10 NEX-7 NEX-6 NEX-5R NEX-5N NEX-5 NEX-C3 NEX-3 NEX-A Tested Lenses The following lenses have been tested for autofocus operation. Minimum firmware version required shown in parenthesis. Thanks to the community for reporting success with lenses shown in bold. Canon EF primes EF L II USM EF L II USM EF IS USM EF L USM (Ver.19) EF L USM EF L II USM EF USM (Ver.18) EF USM macro (Ver.17) EF L USM (Ver.17) EF L II USM (Ver.17) EF L IS USM Extender EF 1.4x III Extender EF 2x (mark I) Canon EF zooms EF L USM fisheye EF L USM EF L (Ver.18) EF USM EF L USM II EF II (Ver.18) EF III EF L (Ver.18) EF L IS USM II EF L USM EF L IS USM EF L IS USM EF IS USM EF (non-L, not USM, push-pull zoom) (Ver.18) EF L IS USM Canon EF-S EF-S USM EF-S IS USM EF-S IS USM EF-S EF-S IS EF-S IS EF-S macro USM Sigma DC DC OS HSM (Ver. DC HSM old version (Ver.18) Tamron SP Di VC USD A007 (Ver.15) SP Di VC USD A009 (Ver.31) Tokina (full frame) (Ver.18) Tokina DX AT-X PRO SD (IF) DX (Ver.15) Note: Sigma OS HSM may occasionally run into a focus accuracy issue at the telephoto end. Manual Focus Only The following lenses have been tested with previous firmware versions with manual focus, aperture control, image stabilization (if applicable) and EXIF support. Autofocus is supported only for those lenses marked with an asterisk (*) on NEX-5R/6 Canon EF primes EF L (mark I) EF USM* EF L USM (mark I) EF (old version, non-IS) TS-E L TS-E EF USM EF II MP-E macro EF L (mark I) EF L USM Canon EF zooms EF L (mark I) EF L IS USM* EF II EF Contax N modified by Conurus Vario-Sonnar Vario-Sonnar Vario-Sonnar Planar Planar Makro-Sonnar (Ver.21) NAM-1 adapter Sigma (full frame) EX HSM EX DG HSM DG HSM (Ver. DG Macro EX DG Macro HSM Sigma DC EX ASPH EX HSM ASPH DC OS HSM EX DC HSM new version (Ver.17) Tamron VC SP SP Di LD A001 Tokina AT-X PRO Zeiss ZE ZE Distagon ZE Distagon ZE Distagon 35/2 ZE Makro-Planar 50/2 ZE Makro-Planar This Smart Adapter is also compatible with fully manual lenses which have no electrical contacts. Customers have reported success with the following fully manual lenses. Samyang Zeiss CP.2 25mm/T2.9 Zeiss CP.mm/T2.1 Note: 1. 1. Lenses not listed above are not tested and they may or may not work. We do our best to resolve any compatibility issue you find but firmware updates are by factory service only and there is a nominal shipping/handling charge. 2. Mount lens on EF Extender 1.4x or 2x first before attaching both on Metabones Smart Adapter. 3. Mount Contax 645 lens on modified NAM-1 first before attaching both on Metabones Smart Adapter. Autofocus Autofocus is supported, with the following known limitations. Autofocus speed is very slow and inadequate for most moving subjects. The autofocus speed is unfit for professional use for sure, and it would disappoint most enthusiasts. Only Canon-branded lenses introduced in or after are officially supported. Autofocus may be disabled for older Canon lenses and most third-party lenses, including most Sigma, Tamron and Tokina lenses and all Contax N lenses modified by Conurus. On NEX camera bodies in camcorder form factor (e.g. FS series), autofocus may be available only in photo mode but not in movie capture mode. Continuous AF is not supported. DMF mode (direct manual focus) is not supported. For non-camcorder camera bodies (e.g. NEX-7), during movie capture, if the subject moves to a different distance, half-press the shutter release button to re-activate autofocus and lock onto the subject again. Since autofocus speed is slow, there may be visible disruption in the resulting footage. The first two autofocus attempts are used to calibrate the lens and as a result may not lock successfully on the target. Half-press the shutter release button again and autofocus will lock successfully. Autofocus may have difficultly locking onto subjects which are very close to the nearest focusing distance of the lens. Autofocus accuracy depends heavily on the working condition of the lens. Lenses with hidden problems which may not be apparent on Canon DSLRs will lead to inaccurate and unreliable autofocus on Sony NEX. Typical problems of this kind that we have seen include an unsmooth/erratic autofocus mechanism (e.g. getting stuck intermittently at a certain focusing distance), a faulty/worn-out distance encoder or other faulty/worn-out internal sensors. Why Metabones? Since its inception, Metabones has been designing and manufacturing lens adapters recognized among professionals and enthusiasts as leaders in design and workmanship. Contrary to the popular trend of other factories using an aluminum ring painted black on the camera-body-side, we instead take no short-cut but use precision-machined brass with chromium plating on both the camera-body and the lens sides of our adapters, in order to ensure smooth mounting, great appearance, and durability. The lens side of the adapter features a strong leaf-spring structure, strengthening the adapter-lens connection and ensuring tightness of the lens in order to reduce wear and prevent focus errors and optical alignment issues from appearing. Metabones uses matte-black treatment to keep internal reflection to a minimum in order to maintain the maximum optical quality possible with the lens. All Metabones Adapters follow this tradition of uncompromising precision, robust build quality and outstanding finish. Our new Smart AdapterTM series of products add industry-leading electronic interfacing technology from Canada, with true electronic control of the lens', aperture directly from the camera body. Features Both camera-side and lens-side of the adapter are made of brass, precision-machined and plated with chromium. Satin surface finish - just like your OEM lens and camera mounts. Precise fit and solid connection - lens has no play, gap or wiggling when mounted on adapter and no adjustments are required to fit your lens. Designed to reach infinity focus while maintaining the correct registration distance required to maintain optical quality of CRC lenses or lenses with floating elements. Our Smart AdapterTM series adapters have the following additional features True electronic integration of aperture diaphragm - let camera automatically choose aperture in P or S exposure modes, or dial in yourself on the camera body in A or M modes. EXIF data such as lens identification, focal length and aperture.